Analog-devices SHARC 82-000805-01 Manual de usuario

SHARC® EZ-Extender®Manual Revision 3.0, April 2006Part Number 82-000805-01Analog Devices, Inc.One Technology WayNorwood, Mass. 02062-9106a

What’s New in This Manualx SHARC EZ-Extender Manual • Appendix B,“EZ-Extender Schematic” on page B-1 Provides the resources to allow modifications to

SHARC EZ-Extender Manual xi Preface• Contact your Analog Devices, Inc. local sales office or authorized distributor• Send questions by mail to: Analo

Product Informationxii SHARC EZ-Extender Manual Registration:Visit www.myanalog.com to sign up. Click Register to use MyAnalog.com. Registration takes

SHARC EZ-Extender Manual xiii PrefaceLIf you plan to use the EZ-KIT Lite board in conjunction with a JTAG emulator, also refer to the documentation t

Product Informationxiv SHARC EZ-Extender Manual Online Technical DocumentationOnline documentation comprises the VisualDSP++ Help system, software too

SHARC EZ-Extender Manual xv PrefaceNotation ConventionsText conventions used in this manual are identified and described as follows. LAdditional conv

Notation Conventionsxvi SHARC EZ-Extender Manual

SHARC EZ-Extender Manual 1-1 1 EZ-EXTENDER INTERFACESThis chapter relates how the extender interfaces with the compatible boards. The information is p

Breadboard Area1-2 SHARC EZ-Extender Manual Switch (SW1)” on page 2-3. The setup of the general-purpose signals DAI_P15_GP1 and DAI_P16_GP2 is depende

SHARC EZ-Extender Manual 2-1 2 EZ-EXTENDER HARDWARE REFERENCEThis chapter describes the hardware design of the SHARC EZ-Extender. The following topic

Copyright Information©2006 Analog Devices, Inc., ALL RIGHTS RESERVED. This document may not be reproduced in any form without prior, express written c

System Architecture2-2 SHARC EZ-Extender Manual The block diagram in Figure 2-1 shows that each clock and general-pur-pose signal attached to the anal

SHARC EZ-Extender Manual 2-3 EZ-Extender Hardware Referenceing a socket with an oscillator. Only one of these sources can be used at a time, the othe

DIP Switches and Jumpers2-4 SHARC EZ-Extender Manual When the SW1 switch connects a direction control signal to ground (GND), the corresponding signal

SHARC EZ-Extender Manual 2-5 EZ-Extender Hardware ReferenceMISO Disconnect Jumper (P6)The MISO signal of the serial peripheral interconnect (SPI) con

DIP Switches and Jumpers2-6 SHARC EZ-Extender Manual

SHARC EZ-Extender Manual A-1 A EZ-EXTENDER BILL OF MATERIALSThe bill of materials corresponds to “EZ-Extender Schematic” on page B-1. Please check t

A-2 SHARC EZ-Extender Manual 10 1 RJ45 8PIN CON_RJ45 J2 TYCO 1-16609214-1 11 1 SMA XPINS CON043 J3 JOHNSON COMP

D4321A B C20 Cotton RoadNashua, NH 03063A B C D4321PH: 1-800-ANALOGDCTitleSize Board No.Date Sheet ofDEVICESANALOGRevA0182-20032.0ADSP21262 EX-EXTENDE

5V5V 5V5VD4321A B C20 Cotton RoadNashua, NH 03063A B C D4321PH: 1-800-ANALOGDCTitleSize Board No.Date Sheet ofDEVICESANALOGRevA0182-20032.0ADSP21262 E

3.3VD4321A B C20 Cotton RoadNashua, NH 03063A B C D4321PH: 1-800-ANALOGDCTitleSize Board No.Date Sheet ofDEVICESANALOGRevA0182-20032.0ADSP21262 EX-EXT

Regulatory Compliance The SHARC EZ-Extender has been certified to comply with the essential requirements of the European EMC directive 89/336/EEC (inc

5V3.3VD4321A B C20 Cotton RoadNashua, NH 03063A B C D4321PH: 1-800-ANALOGDCTitleSize Board No.Date Sheet ofDEVICESANALOGRevA0182-20032.0ADSP21262 EX-E

3.3V3.3V 3.3V3.3VD4321A B C20 Cotton RoadNashua, NH 03063A B C D4321PH: 1-800-ANALOGDCTitleSize Board No.Date Sheet ofDEVICESANALOGRevA0182-20032.0ADS

3.3V3.3V 3.3V 3.3V3.3V 3.3V3.3VD4321A B C20 Cotton RoadNashua, NH 03063A B C D4321PH: 1-800-ANALOGDCTitleSize Board No.Date Sheet ofDEVICESANALOGRevA0

D4321A B C20 Cotton RoadNashua, NH 03063A B C D4321PH: 1-800-ANALOGDCTitleSize Board No.Date Sheet ofDEVICESANALOGRevA0182-20032.0ADSP21262 EX-EXTENDE

SHARC EZ-Extender Manual I-1 IINDEXAADC (analog-to-digital converter) interface, 1-1, 2-2address bus, 2-3ADSP-21262 processorsclock in signal (DAI_PP

INDEXI-2 SHARC EZ-Extender Manual Jjumpers, 2-3clock disconnect (P10), 2-5MISO disconnect (P6), 2-5MMISO disconnect jumper (P6), 2-5Nnotation conventi

iv SHARC EZ-Extender Manual

SHARC EZ-Extender Manual v CONTENTSPREFACEPurpose of This Manual ... viiiIntended Audi

CONTENTSvi SHARC EZ-Extender Manual DIP Switches and Jumpers ... 2-3Direction/Clock Source C

SHARC EZ-Extender Manual vii PREFACEThank you for purchasing the SHARC® EZ-Extender®, Analog Devices (ADI) extension board to the EZ-KIT Lite® evalua

Purpose of This Manualviii SHARC EZ-Extender Manual The board extends the capabilities of the evaluation system by providing a connection between the

SHARC EZ-Extender Manual ix PrefaceIntended AudienceThis manual is a user’s guide and reference to the SHARC EZ-Extender. Programmers who are familia